Body Shop

7

cuda full rear quarter panel body line questions I'm in the process of hanging my new AMD passenger side rear quarter panel.  The body lines from the...

Started by 72restocudaView the profile of 72restocuda

Replies: 1
Views: 603

January 22, 2024, 02:44:05 PM
by 72restocuda

73-74 cuda-challenger rear bumper filler panel correct paint? I added pictures of a corner and the center piece I'm in the process of setting the gaps on the trun...

Started by DannytheanglerView the profile of Dannytheangler

Replies: 7
Views: 1,295

January 22, 2024, 07:21:43 AM
by anlauto

7

71 cuda fender turn signal cutout template bought new 71 fenders from AMD, would like to have correct looking 71 fender mounted turn signal ind...

Started by 72restocudaView the profile of 72restocuda

Replies: 0
Views: 505

January 19, 2024, 06:13:29 PM
by 72restocuda

Quarter Glass Loose in Frame The quarter glass in very loose in my Cuda to the point that it will not close properly.   I suspect...

Started by BluRaySRTView the profile of BluRaySRT

Replies: 6
Views: 1,524

January 13, 2024, 06:52:35 PM
by Rich G.

Putting part numbers into new replacement parts I've learned various sheet metal parts I intend to replace have part numbers stamped in them. I'm le...

Started by 71challyView the profile of 71chally

Replies: 8
Views: 1,455

January 06, 2024, 04:03:02 PM
by MoparLeo

Silver or chrome? I want to freshen up the border of the A/C vents in the dash. I'm going to try it, in place, with a ...

Started by blown motorView the profile of blown motor

Replies: 1
Views: 538

January 06, 2024, 01:41:16 PM
by MoparLeo

T

Trunk Floor Replacement My '70 Challenger had a two-piece trunk-floor replacement performed 20 years ago.  Now, this replace...

Started by Roberts440View the profile of Roberts440

Replies: 10
Views: 2,501

January 05, 2024, 04:58:01 PM
by tparker

M

Ducktail Spoiler Was a ducktail spoiler available from the factory on a non AAR Cuda? Thanks

Started by SeventyTX9RTRagView the profile of SeventyTX9RTRag

Replies: 3
Views: 1,020

January 04, 2024, 04:10:02 PM
by Mixup7071

1

Wheel lip molding screws for cuda is pn# 6028545, AMK# B-12237 correct for the fender well moldings on a 1970 cuda?....Thank you, Joe

Started by 1970 cuda JoeView the profile of 1970 cuda Joe

Replies: 3
Views: 411

January 02, 2024, 03:54:24 PM
by 1970 cuda Joe

M

Lower sill blackout https://www.e-bodies.org/Resources/Engineering_Illustrations/Black_Out_Sill_Lower_Cuda.pdfThis (1969...

Started by Mrbill426View the profile of Mrbill426

Replies: 4
Views: 1,129

December 29, 2023, 01:34:02 PM
by Mrbill426

X

71 Cuda rear taillight bezels restoration Looking into restoring by tail light bezel. I know they sell reproductions but rather keep originals...

Started by 440ehighView the profile of 440ehigh

Replies: 3
Views: 835

December 28, 2023, 05:02:52 PM
by Xghobo

Question on rust development This is just a question that ran through my mind. So, moisture needs to be present for rust to start...

Started by blown motorView the profile of blown motor

Replies: 8
Views: 2,217

December 27, 2023, 06:36:20 PM
by cudamadd

Black Engine Bay / Ziebart Treatment Over the years there have been some questions about black engine bays and Ziebart treatments.  I cam...

Started by PLY474View the profile of PLY474

Replies: 3
Views: 1,025

December 27, 2023, 06:21:07 AM
by torredcuda

26" Radiator Support Measurement All, What is the measurement length wise for the bolt holes (top and bottom) on a 26" radiator suppo...

Started by erik70rtView the profile of erik70rt

Replies: 5
Views: 1,152

December 26, 2023, 05:57:31 PM
by erik70rt

1

1970 cuda blackouts The 1970 cuda I purchased was built sometime in mid to late November according to the VIN (no fender...

Started by 1970 cuda JoeView the profile of 1970 cuda Joe

Replies: 8
Views: 2,153

December 24, 2023, 05:14:31 AM
by 1970 cuda Joe

J

Fixing rocker panel rust My 2012 Fusion has blisters coming up through the paint in the lower rocker under both rear side doo...

Started by HoodView the profile of Hood

Replies: 1
Views: 421

December 20, 2023, 07:11:53 PM
by jimynick

J

using 3m panel bond as seam sealer in trunk area I'm sure this has been asked before but I haven't found it.  Using panel bond between panels in the ...

Started by 72restocudaView the profile of 72restocuda

Pages1 2

Replies: 16
Views: 3,912

December 16, 2023, 06:39:08 PM
by jimynick

J

Cutting Out A PIllar Seam and Sail Panel Seam I've been watching some youtube videos, and noticed people cutting out sail panel seams/a pillar sea...

Started by 71challyView the profile of 71chally

Replies: 1
Views: 329

December 15, 2023, 09:34:56 PM
by jimynick

D

Front floor pans Generally does everyone replace the entire piece, or just cut out the bad metal. I have mint OEM flo...

Started by 71challyView the profile of 71chally

Replies: 2
Views: 425

December 13, 2023, 09:11:59 AM
by DeathProofCuda

D

Install Go wing on a 70 Challenger I seem to recall that to properly install a go wing, I need to pinch it between the layers of the de...

Started by CHL2TView the profile of CHL2T

Replies: 5
Views: 1,276

December 11, 2023, 09:08:06 AM
by DeathProofCuda