Engine, Transmission & Rear End

727 Transmission oil Hi,I have a 727 auto in my 70 challenger. looking for transmission fluid.Is there a specific product...

Started by CdnchallengerView the profile of Cdnchallenger

Replies: 3
Views: 616

June 12, 2024, 12:14:12 PM
by MoparLeo

G

clutch fan spacing When trying to set the fan so it is far enough into the shroud (I think I've read 2/3 of the fan bla...

Started by Gross PolluterView the profile of Gross Polluter

Replies: 6
Views: 649

June 10, 2024, 09:38:51 PM
by Gross Polluter

T

cleaning corrosion on alt & carb linages I pulled the tarps off my car after this winter the other day and I have what I think is corrosion o...

Started by tparkerView the profile of tparker

Replies: 2
Views: 393

June 06, 2024, 03:56:41 PM
by tparker

Throtal Kickdown Linkage I have an original 318 2 barrel car that I replaced with a 340 and a late model thermaquade in 1990....

Started by tparkerView the profile of tparker

Replies: 11
Views: 765

June 05, 2024, 06:57:47 PM
by Jay Bee

4

Transmission Identificaton Hi. Can anyone help me identify this transmission? It's currently in a 1970 Cuda. Thanks.

Started by 4SpeedT/AView the profile of 4SpeedT/A

Replies: 4
Views: 328

May 28, 2024, 04:10:13 AM
by 4SpeedT/A

K Member Identification Hi. Can anyone help me identify this K member? I believe the numbers are 278032. It's on a 1970 Cuda...

Started by 4SpeedT/AView the profile of 4SpeedT/A

Replies: 3
Views: 357

May 27, 2024, 03:22:13 PM
by 6bblgt

Changing coolant I need to change the coolant in my 340. After I drain the rad should I remove the plugs, one on each...

Started by blown motorView the profile of blown motor

Replies: 3
Views: 332

May 26, 2024, 05:46:36 PM
by 71GranCoupe

340 Rocker Mount Question I went to install my rocker arms last night and I noticed that the usual "cradles" on the heads wher...

Started by erik70rtView the profile of erik70rt

Replies: 10
Views: 857

May 24, 2024, 06:47:55 AM
by RUNCHARGER

Distributor Vacuum Advance Issue While a friend and I were carb adjusting to make my car idle nice he found that the distributor's pl...

Started by Jay BeeView the profile of Jay Bee

Replies: 5
Views: 533

May 19, 2024, 05:32:28 AM
by 73_Cuda_4_Me

Help with 1-2 hesitation after Sniper install I'm running a Sniper on a 318 904 tranny, 8-3/4 and have noticed a few issues.  I know I have to RTF...

Started by 70pumpkinView the profile of 70pumpkin

Replies: 3
Views: 486

May 17, 2024, 04:15:46 PM
by Skdmark

Help Diagnosing Clutch Noise I am getting a high pitch squealing noise when releasing clutch.  It is particularly noticeable when...

Started by BluRaySRTView the profile of BluRaySRT

Replies: 4
Views: 779

May 15, 2024, 10:03:03 AM
by BluRaySRT

T

Mancini Gen 3 motor mounts I'm putting a 392 hemi into my 1970 Challenger convertible and getting ready to install the engine i...

Started by TripleBlk70View the profile of TripleBlk70

Replies: 0
Views: 256

May 14, 2024, 07:04:35 PM
by TripleBlk70

bolt size between tail housing and case Hi What's the size, diameter and lenght, of bolts between tail housing and case on the 727?

Started by chal340View the profile of chal340

Replies: 0
Views: 301

May 04, 2024, 12:12:36 AM
by chal340

S

8HP70 -> 8HP90 on my '70 Cuda - what are differences? Hi,I have an 8HP70 nicely fitted onto my 70 Cuda and sitting behind a 5.7 Hemi. However, I would lik...

Started by speedbird1229View the profile of speedbird1229

Replies: 3
Views: 1,043

May 03, 2024, 12:07:58 AM
by speedbird1229

All kick down linkage identification @VCODE  had a wanted for some carb to kick down linkage. I said, hey I'm wasting time already,  so l...

Started by Mr CudaView the profile of Mr Cuda

Replies: 9
Views: 1,119

April 28, 2024, 05:26:14 AM
by Mr Cuda

P

426 hemi and dual Edelbrocks - fuel fittings? Hi I have installed my newly rebuilt 496 hemi with dual 1406 Edelbrocks. The carbs does not have cor...

Started by andbenView the profile of andben

Replies: 2
Views: 366

April 25, 2024, 05:00:37 PM
by PsyOps

G

Starter Gear Noise I hear a noise that I think is from the starter motor that only occurs just as the engine starts and...

Started by Gary AARView the profile of Gary AAR

Replies: 3
Views: 567

April 20, 2024, 07:36:51 AM
by Gary AAR

340 rockerarms How much tolerance are accepted between shaft and rockerarms? I have slight ticking and i checked so...

Started by Qda71View the profile of Qda71

Replies: 3
Views: 554

April 19, 2024, 11:34:17 AM
by Chryco Psycho

S

Help needed - Red Eye swap to 70 Cuda Hi,I need some help purchasing a new oil pan for my 70 Cuda project. I acquired a brand new Red Eye ...

Started by speedbird1229View the profile of speedbird1229

Replies: 4
Views: 442

April 19, 2024, 03:17:10 AM
by speedbird1229

Trans rear seal Yesterday I changed the rear seal on my 727. I get under the car today to change the transmission fl...

Started by xx88manView the profile of xx88man

Replies: 7
Views: 1,116

April 16, 2024, 09:25:46 PM
by Chryco Psycho