Print Page - Shaker Cold Air cable question.

Title: Shaker Cold Air cable question.
Post by: usraptor on April 27, 2018, 05:01:33 PM

I ordered a new Cold Air cable for my shaker assembly a couple of year ago; the one that connects under the dash with the red label. I went to hook it up to my Shaker base today it is extends several inches past the bell crank that it's supposed to connect to. Did they make different length cables and I got the wrong one? Routed wrong?? Any ideas would be appreciated. :help:

Title: Re: Shaker Cold Air cable question.
Post by: Plumcrazzy on April 27, 2018, 05:37:41 PM

Just hook it up and let the slack take care of itself. You can clip the slack to any available location if it rubs anything.

Title: Re: Shaker Cold Air cable question.
Post by: anlauto on April 27, 2018, 05:55:58 PM

Slack is taken up inside the car usually :alan2cents:

Title: Re: Shaker Cold Air cable question.
Post by: usraptor on April 27, 2018, 06:24:34 PM

Thanks guys. :twothumbsup: :worship:

Title: Re: Shaker Cold Air cable question.
Post by: fc7cuda on April 28, 2018, 05:50:18 AM

Is it mounted where the vent cables go? That would be too close and cause excessive slack. Otherwise, there is supposed to be some slack to allow for motor movement and installation.

I have an original one if you need a measurement, LMK.

:cheers:

Title: Re: Shaker Cold Air cable question.
Post by: usraptor on April 30, 2018, 08:08:23 AM

fc7cuda, when you say "is it mounted where the vent cable go?" do you mean under the dash or where it comes out of the firewall? If you're referring to under the dash, yes it's mounted next to the fresh air vent cables, but that's the way it was originally so I don't understand why that would cause excessive slack. :dunno:
If you could grab a quick measurement of your cable it would be greatly appreciated. :twothumbsup:

Title: Re: Shaker Cold Air cable question.
Post by: usraptor on April 30, 2018, 09:06:31 AM

fc7cuda, your post about the cables being next to the vent pulls got me thinking and I started doing some research. Come to find out your are correct! :worship: :clapping: I had the cable attached to the dash in the wrong place per pics of what I believe to be a 71 dash layout instead of a 1970. After crawling under my dash I located the holes under the radio to mount the "Carb Air" cable to. Hopefully I'll get to it later today. After being in the 80s all weekend it's snowing again this morning. Gotta love Utah weather. :looney: If you don't like it, just wait five minutes. Thanks for the suggestion. :twothumbsup:

Title: Re: Shaker Cold Air cable question.
Post by: anlauto on April 30, 2018, 09:59:21 AM

The above picture is the wrong location.

Title: Re: Shaker Cold Air cable question.
Post by: usraptor on May 02, 2018, 09:48:21 AM

Alan, it goes under the radio correct?

Title: Re: Shaker Cold Air cable question.
Post by: culp71 on May 02, 2018, 09:56:06 AM

yes on the corner like this

Title: Re: Shaker Cold Air cable question.
Post by: usraptor on May 02, 2018, 09:57:49 AM

Thanks culp71 :twothumbsup: :worship:

Title: Re: Shaker Cold Air cable question.
Post by: culp71 on May 02, 2018, 10:03:15 AM

you got it! one more pic for a little more detail.

E-Bodies.org Cuda Challenger Forum

Technical Shop => Engine, Transmission & Rear End => Topic started by: usraptor on April 27, 2018, 05:01:33 PM