normal_post in O/D 4 speed synchro sliders in Engine, Transmission & Rear End Author Topic: O/D 4 speed synchro sliders  (Read 179 times)

Offline GoMangoBoys

  • Trade Count: (0)
  • Big Block
  • ***
  • Location: Copley Ohio
  • index in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
  • Posts: 302
  • Credits: 2350
    • Share Post
xx in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
O/D 4 speed synchro sliders
« on: January 13, 2020, 08:12:19 PM »
We are starting the rebuild of the OD transmission that I bought for the 70 Challenger.  The 3-4 synchro slider is a bit beat up.  We are going to replace it.  My friend who is helping us is a MAJOR Muncie and Borg Warner expert.  HE builds a lot of those and has parts to build over 250 transmissions.  In doing an initial compare, he said it looks like the slider that I need is identical to the one for the Borg-Warner Super T10.  Does anyone have any knowledge to confirm or reject this idea?  We intend to make more digital caliper measurements tomorrow, but he said that the slider slides right onto the gears just fine.  We intend to measure everything related to the interface to the shift forks to be sure that they are the same there as well.
Any input is appreciated.
FYI, I bought the rebuild kit from Brewers, it is coming tomorrow.  If the Super T10 slider is not a good match then I need to order one from them.
Thanks

Linkback: https://forum.e-bodies.org/engine-transmission-and-rear-end/4/od-4-speed-synchro-sliders/14422/

Offline Chryco Psycho

  • Global Moderator
  • Trade Count: (0)
  • E-Body Wizard
  • *****
  • Location: Coronado Panama
  • index in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
  • Posts: 15020
  • Credits: 33200
  • Challenger ... You'll wish you hadn't !!
    • Share Post
xx in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
Re: O/D 4 speed synchro sliders
« Reply #1 on: January 14, 2020, 09:21:00 PM »
I have never tried to swap parts from a Borg Warner trans .
 If ti doesn't match up I would recommend Brewers or Passon Perf for replacement parts
1-190417082201 in O/D 4 speed synchro sliders in Engine, Transmission & Rear End

Offline RUNCHARGER

  • Trade Count: (7)
  • E-Body Wizard
  • *****
  • Location: .Vernon B.C.
  • index in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
  • Posts: 10358
  • Credits: 32990
    • Share Post
xx in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
Re: O/D 4 speed synchro sliders
« Reply #2 on: January 15, 2020, 08:13:00 AM »
I doubt it would fit, most of the GM stuff is alot lighter than the A833 parts. All you can do is compare them side by side I think. Whenever the GM guys brag about how many Muncies they break, I tell them to swap in an A833, then they'll start breaking rear ends instead.
Sheldon

E-Bodies Cuda Challenger Message Forum

xx in O/D 4 speed synchro sliders in Engine, Transmission & Rear End
Re: O/D 4 speed synchro sliders
« Reply #2 on: January 15, 2020, 08:13:00 AM »

Tags:

Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter Share via whatsapp

xx
73 seat sliders

Started by Crash520

6 Replies
503 Views
Last post February 21, 2017, 05:12:32 PM
by Crash520
xx
Trans crossmember 3 speed vs. 4 speed?

Started by dave73

3 Replies
505 Views
Last post October 31, 2017, 07:17:29 PM
by Chryco Psycho
xx
Wanted AAR 4 speed, or U code 4 speed. U code could be Challenger or Cuda

Started by SeventyTX9RTRag

13 Replies
984 Views
Last post November 18, 2019, 09:23:09 PM
by nsmall
xx
What oil do you use in your 4 speed?

Started by Shoooter

12 Replies
598 Views
Last post April 19, 2019, 10:48:12 PM
by Chryco Psycho
xx
Is this a 70 3 speed?

Started by cuda hunter

2 Replies
172 Views
Last post March 09, 2019, 08:00:03 PM
by 6bblgt