Engine, Transmission & Rear End

Big Block Mopar Engine Dolly Suggestions Hey all, I am looking for an engine dolly / stand for a big block Mopar similar to this one from Jeg...

Started by 70_440-6CudaView the profile of 70_440-6Cuda

Replies: 4
Views: 108

Today at 07:22:46 AM
by 70_440-6Cuda

340 Engine vs 392 Hemi All,I have been strongly considering installing a 392 Crate in my 1973 Barracuda. The car currently ...

Started by StanPView the profile of StanP

Pages1 2

Replies: 20
Views: 831,753

April 30, 2025, 01:22:00 PM
by Katfish

M

6-Pack emblem location I'm finally getting close to having my car painted. It's been a long process with extensive metal wo...

Started by Indiana Challenger GuyView the profile of Indiana Challenger Guy

Replies: 13
Views: 484

April 28, 2025, 05:19:27 AM
by mtull

M

Help Identifying Ring and Pinion Hi all, got my old ring and pinion back and can't seem to track down what I have here, any help with...

Started by 70_440-6CudaView the profile of 70_440-6Cuda

Replies: 4
Views: 297

April 26, 2025, 07:49:12 AM
by moonshine_mike

New vs Restore Fuel Tank I have an old fuel tank that the fuel turned to varnish then during the cleaning it got a lot of sur...

Started by tparkerView the profile of tparker

Pages1 2

Replies: 19
Views: 1,811

April 25, 2025, 04:27:52 PM
by 1970Cuda

Opinions wanted I'm going to put a micro electric fuel pump on my Challenger for easier starting. I've outlined two ...

Started by blown motorView the profile of blown motor

Replies: 7
Views: 336

April 24, 2025, 07:09:35 AM
by ec_co

six pack air cleaner parts question Are non-fresh-air six-pack air cleaners being reproduced at this time?  I need a base plate to compl...

Started by DuodecView the profile of Duodec

Replies: 6
Views: 501

April 18, 2025, 05:40:01 PM
by Duodec

Small block 727 dust cover reinstallment Ready to reinstall 340 . Transmission is sitting up and supported MY Question does the starter stud ...

Started by cudamaddView the profile of cudamadd

Replies: 0
Views: 90

April 17, 2025, 11:06:45 PM
by cudamadd

B

73 challenger tti headers I just got my headers installed. Engine is 408 with 1 7/8 primaries and 3.5 inch collectors. Headers...

Started by 73ralyeView the profile of 73ralye

Replies: 2
Views: 133

April 17, 2025, 10:34:55 PM
by bdschnei

B

F383 Engine Stamp Hi Guys,I just recently found a F383 HP for my R/T build and had a question for you guys. The castin...

Started by BlowoutView the profile of Blowout

Replies: 0
Views: 86

April 17, 2025, 11:37:34 AM
by Blowout

H

Maximum compression ratio I am doing a 360 / 408 build using the Trick Flow heads.  What is is the maximum compression ratio t...

Started by GoMangoBoysView the profile of GoMangoBoys

Replies: 4
Views: 211

April 16, 2025, 06:40:40 PM
by HP2

P

727 w/overdrive #s match 73 340 Cuda w/727 auto, 2500 stall converter, 323 gears. stock 15" tires, 4000+ rpm @ 70 mp...

Started by GlideView the profile of Glide

Replies: 11
Views: 594

April 16, 2025, 10:26:12 AM
by PLUM72

7

1970 A833 require bushings on the transmission levers, shift rods or shifter Hi Everyone, Full disclosure A am working on my Duster 340 here but the question should be the same....

Started by 72 ChallengerView the profile of 72 Challenger

Replies: 2
Views: 138

April 16, 2025, 04:12:09 AM
by 72 Challenger

Need Advice: - A833 OD Built for Longer Life Behind Street/Strip Stroker Need some advice/help.  My car set up is a street strip (90% street/cruise/car show) 73 Barracuda, s...

Started by the_cuda_guyView the profile of the_cuda_guy

Pages1 2

Replies: 17
Views: 658

April 12, 2025, 08:28:32 PM
by the_cuda_guy

Pilot bearing vs Pilot Bushing Looking for pinions on using a pilot bearing vs a pilot bushing.  The bushing seems like the better ...

Started by GoMangoBoysView the profile of GoMangoBoys

Replies: 7
Views: 254

April 12, 2025, 03:57:15 AM
by torredcuda

This has to be the same product, doesn’t it? Micro electric fuel pump. Both have same pressure rating and GPH. Both come with same filter and bol...

Started by blown motorView the profile of blown motor

Replies: 9
Views: 429

April 10, 2025, 06:06:42 AM
by blown motor

Z bar 318 /383 are they the same Working on 1970 Challenger was a 318 4spd car ,put a 1971 383 in it reused z bar flywheel clutch pre...

Started by Gregg1View the profile of Gregg1

Replies: 2
Views: 190

April 06, 2025, 10:46:44 AM
by ec_co

R

What does this pulley go to Bought what I thought was a crank pulley for my 340 off EBay since the one I currently have has a wo...

Started by RdchallengerView the profile of Rdchallenger

Replies: 3
Views: 274

April 06, 2025, 07:41:51 AM
by Rdchallenger

H

340 engine I have this 340 engine laying around. How do I determine what flywheel or torque converter I would n...

Started by Rich G.View the profile of Rich G.

Replies: 6
Views: 347

April 02, 2025, 03:34:59 PM
by HP2

Auto to Manual How much work What does it take to swap an auto to manual, other than the obvious? Does anything need to be cut up...

Started by tparkerView the profile of tparker

Pages1 2

Replies: 21
Views: 1,906

March 29, 2025, 09:10:50 AM
by dodj