Stumped by the stupidest thing...how do you get this breather off?

72 Challenger · January 15, 2018, 07:40:54 AM

I have attached a picture. How do you get the black breather off? Sometimes the stupidest things.

Spikedog08 · January 15, 2018, 07:45:01 AM

As far as I know . . . PULL.

Wiggle, pull, wiggle, pull

Jim AAR · January 15, 2018, 07:48:56 AM

Sometimes you have to bend it as far over as you can while lifting, some are really tight.

TelisSE440 · January 15, 2018, 07:50:12 AM

χ2 Pull and wiggle... vigorously!

72 Challenger · January 15, 2018, 07:55:27 AM

Alright more ooomph. On it. I was afraid to screw up the covers.

nsmall · January 15, 2018, 08:00:35 AM

If you get stumped...post. Thats what this site is here for. I get stumped weekly, but I am glad people here are glad to help out.

anlauto · January 15, 2018, 08:09:01 AM

PULL !

1 Wild R/T · January 15, 2018, 08:12:26 AM

And if it's really hard pull some more... Wait, that didn't come out right....

But seriously if the engine has been run sometimes the grommet gets cooked & becomes rock hard if thats the case replacing the grommet will make it easier to remove & reinstall in the future...

nsmall · January 15, 2018, 08:15:05 AM

I bought some grommets from Mancini Racing and they are really nice. Not sure if they sell some for OEM valve covers. Did you get it off?

71-440 · January 15, 2018, 04:02:34 PM

Quote from: nsmall on January 15, 2018, 08:15:05 AM
I bought some grommets from Mancini Racing and they are really nice. Not sure if they sell some for OEM valve covers. Did you get it off?

I think he's still pulling....

GY3R/T · January 15, 2018, 04:34:31 PM

Twist and Shout....

RUNCHARGER · January 15, 2018, 06:26:22 PM

You can insert a thin piece of wood on the valvecover and lever it off with a screwdriver if need be. The grommet is rock hard no doubt.

72 Challenger · January 16, 2018, 11:31:38 AM

Well I pulled, I pried and I PULLED and I....broke the breather.

This is the most Frustrating enjoyable hobby you can have! lol. I just want to paint my engine back to the correct corporate blue damnit.

ToxicWolf · January 16, 2018, 12:02:11 PM

Quote from: 72 Challenger on January 16, 2018, 11:31:38 AM
Well I pulled, I pried and I PULLED and I....broke the breather.

This is the most Frustrating enjoyable hobby you can have! lol. I just want to paint my engine back to the correct corporate blue damnit.

Mopar ... Frustration ... Sounds right to me

We've all been there.

71-440 · January 16, 2018, 01:15:54 PM

Quote from: 72 Challenger on January 16, 2018, 11:31:38 AM
Well I pulled, I pried and I PULLED and I....broke the breather.

This is the most Frustrating enjoyable hobby you can have! lol. I just want to paint my engine back to the correct corporate blue damnit.

LOL... At least you got it off.

Close, but no start, stumped Started by Katfish on Modern Hemi Swaps	7 Replies 886 Views	Last post: October 25, 2022, 06:00:59 PM by Chryco Psycho
Stupidest "speed trick" you ever did ? Started by Racer57 on Cuda & Challenger General Discussion (ROSEVILLE MOPARTS)	1 Replies 462 Views	Last post: February 06, 2020, 01:51:21 PM by Daveh
Air breather. WIW Started by blown motor on What's It Worth?	25 Replies 2034 Views	Last post: April 18, 2019, 07:12:37 AM by 1 Wild R/T
Air breather question Started by blown motor on Engine, Transmission & Rear End	9 Replies 1091 Views	Last post: January 06, 2021, 07:27:36 PM by MoparLeo
Correct breather for a 440-6 Started by Ric on Engine, Transmission & Rear End	13 Replies 1235 Views	Last post: December 26, 2018, 10:03:55 AM by anlauto