70 challenger - gear shift linkage is short

mtterry · November 13, 2022, 04:12:59 PM

Trying to hook up the transmission gear linkage. We are finding the gearshift control lever appears different than what's shown in the service manual. We are about an inch or two short. Pic is what I have. 727 / 383 1970 challenger... Tell a noob what I have mismatched or wrong lol.

Sent from my SM-G986U using Tapatalk

anlauto · November 13, 2022, 06:15:41 PM

Are you saying the black rod in the back is not reaching the vertical shaft from the interior ? Is both the transmission and the shifter in park ? Tranny could be is 1st ?

mtterry · November 13, 2022, 07:39:05 PM

Quote from: anlauto on November 13, 2022, 06:15:41 PM
Are you saying the black rod in the back is not reaching the vertical shaft from the interior ? Is both the transmission and the shifter in park ? Tranny could be is 1st ?

The rod that attaches to the gear shift on the tranny will not reach when the transmission is in park and the floor shifter is in park. I can shift through each individually fine

Sent from my SM-G986U using Tapatalk

anlauto · November 14, 2022, 05:04:08 AM

The transmission is in park when the lower lever on the side is all the way towards the BACK of the car correct ? It's hard to tell in your picture, but it looks to be all the way forward, in 1st gear

mtterry · November 14, 2022, 05:29:39 AM

Quote from: anlauto on November 14, 2022, 05:04:08 AM
The transmission is in park when the lower lever on the side is all the way towards the BACK of the car correct ? It's hard to tell in your picture, but it looks to be all the way forward, in 1st gear

I'll have to look again. But regardless in park ,(linkage) it can't reach the lever in any position

Sent from my SM-G986U using Tapatalk

anlauto · November 14, 2022, 05:41:28 AM

oh...hard to tell I guess in your picture....it looks pretty darn close to me, you're just missing the adjuster block that connects the rod to the vertical lever

mtterry · November 14, 2022, 02:38:30 PM

Quote from: anlauto on November 14, 2022, 05:41:28 AM
oh...hard to tell I guess in your picture....it looks pretty darn close to me, you're just missing the adjuster block that connects the rod to the vertical lever

I went and looked at it today.... And let's chalk it up to a long day haha. I think we are good. Just brain farting. When looking at the service manual the transmission lever looked like it was curved, when ours was straight out.

Sent from my SM-G986U using Tapatalk

anlauto · November 14, 2022, 07:44:31 PM

So you got it all sorted out

727 floor shift linkage mod for TTI headers Started by Kruzkraft on Engine, Transmission & Rear End	21 Replies 2712 Views	Last post: December 02, 2018, 08:25:09 AM by Kruzkraft
727 Shift Kit Question. Do I need a kickdown cable/linkage? Started by 73Challengr on Engine, Transmission & Rear End	8 Replies 1166 Views	Last post: April 23, 2021, 11:23:42 PM by 1972V21Cuda
Conversion carb linkage and down shift lto nkage Q. Started by malem2us on Cuda & Challenger General Discussion (ROSEVILLE MOPARTS)	2 Replies 592 Views	Last post: November 19, 2019, 04:31:19 PM by Chryco Psycho
Changing the gear shift selector bulb Started by bc3j on Interior	7 Replies 772 Views	Last post: August 29, 2018, 01:09:05 PM by CudaMoparRay
Passing gear linkage Started by Timbbuc2 on Parts Wanted	8 Replies 1106 Views	Last post: April 30, 2017, 03:27:43 PM by Timbbuc2