Engine, Transmission & Rear End

Stock 340 Rebuild - Roller Cam? Machine shop recommends a roller cam and lifters for my stock 340 rebuild.  Thoughts? 

Started by Yellow71CudaView the profile of Yellow71Cuda

Pages1 2 3

Replies: 31
Views: 6,323

June 20, 2017, 10:00:08 PM
by Plum_crazy_T/A

Carb size for my setup My Barracuda is really sucking down the gas - approx. 6 mpg in it's current setup.  It has a 416 str...

Started by erik70rtView the profile of erik70rt

Pages1 2 3 ... 5

Replies: 68
Views: 7,299

June 20, 2017, 08:02:36 AM
by erik70rt

T/A rear end I was talking to someone and they said, a friend had a 70 pink T/A with a DANA 60 in it. He is the o...

Started by pink aarView the profile of pink aar

Replies: 8
Views: 1,058

June 19, 2017, 06:57:03 PM
by Chryco Psycho

B

Shifter plate swap Does anyone have any advice on how to get this top half of a slapstick shifter off?I unscrewed one s...

Started by nsmallView the profile of nsmall

Replies: 7
Views: 1,139

June 19, 2017, 09:18:51 AM
by Burdar

518 soft shifts  I've had a 518 for a few years now, I've never liked the way it's shifts. Way to soft, it has a tra...

Started by LeanburnView the profile of Leanburn

Replies: 8
Views: 1,423

June 19, 2017, 08:48:47 AM
by 1 Wild R/T

A833 4 speed shift feel improvements? My 73 Cuda 340 4 speed is great but it's getting to be a pain in the ass to shift.  No grinds or pop...

Started by FSHTAILView the profile of FSHTAIL

Replies: 13
Views: 6,183

June 18, 2017, 04:12:27 PM
by HP_Cuda

G

440 Six Pack....pick my flexplate (with pic) I currently have 2 flexplates to choice from.Engine is a mild rebuilt forged crank 440 with Six Pack...

Started by GrandpaKevinView the profile of GrandpaKevin

Replies: 7
Views: 1,820

June 16, 2017, 06:48:36 PM
by GrandpaKevin

Need help tweaking my clutch and gas pedal I have 2 things going on I'm looking for some advice on how to make them better:Clutch pedal - stock...

Started by dave73View the profile of dave73

Replies: 12
Views: 2,036

June 16, 2017, 01:29:36 PM
by Shane Kelley

M

Moving the springs inboard & using a B body housing.... First time I did this was back in the 80's... It's a great swap.... My buddy has wanted to do it for...

Started by 1 Wild R/TView the profile of 1 Wild R/T

Pages1 2

Replies: 24
Views: 5,015

June 16, 2017, 01:25:43 PM
by MoparJunkie

727 Auto to 833 4 Speed Conversion I really really want a 4 speed in my '70 Cuda that currently has a 727 full manual auto with a 392 H...

Started by 303 MoparView the profile of 303 Mopar

Pages1 2 3 ... 6

Replies: 76
Views: 12,216

June 16, 2017, 10:25:03 AM
by Sleepychallenger

Crate Hemi Disaster Hey guys, I posted this on c-c but wanted to post it here as well.Sorry guys been quite busy, Ok so ...

Started by cordodgeView the profile of cordodge

Pages1 2

Replies: 24
Views: 3,166

June 16, 2017, 10:07:42 AM
by Oldschool

Stock '71 340 Rebuild - Pistons and Cam Selection    I'm keeping the stock exhaust manifolds and carb.  Pretty much a stock rebuild.  Please share you...

Started by Yellow71CudaView the profile of Yellow71Cuda

Replies: 13
Views: 3,156

June 15, 2017, 09:04:34 PM
by Cuda Cody

Choke thermostat Where is the best place to get a choke thermostat for a 70 four barrel 383 Cuda?  Looked on ebay.  T...

Started by jlemlerView the profile of jlemler

Replies: 8
Views: 1,288

June 15, 2017, 05:57:53 PM
by 73440

1970 440-6 Pack Choke Setting Help I was looking at OE the choke thermostat for my 70  6 pack car and I noticed that you can set the ra...

Started by ConvertcudaView the profile of Convertcuda

Replies: 1
Views: 1,489

June 14, 2017, 08:13:23 PM
by Chryco Psycho

Angle Oil Filter Adapter Bolt What is the torque spec for tightening the bolt on the angled oil filter adapter on a small block? 

Started by erik70rtView the profile of erik70rt

Pages1 2

Replies: 22
Views: 5,714

June 12, 2017, 09:38:11 AM
by 1 Wild R/T

Do I need the two front oil galley plugs installed? 340Putting my timing cover back on and looking for info to do it right, no leaks.....hopefully. I fo...

Started by Cudakiller70View the profile of Cudakiller70

Replies: 6
Views: 1,932

June 10, 2017, 02:35:55 PM
by Cudakiller70

Driveline angles and TKOs I was looking to finish off the drive line this weekend on the Challenger by measuring for a drive s...

Started by shawgeView the profile of shawge

Replies: 8
Views: 1,835

June 07, 2017, 05:53:03 PM
by Brads70

7

Spray Bomb Paint Mopar Orange Wanted to hear if others have used this brand/p/n and what they thought on it's pantone.http://www.e...

Started by TopcatView the profile of Topcat

Replies: 14
Views: 2,357

June 07, 2017, 04:40:14 AM
by 750-h2

Proven 340 Engine Combos Please share your proven 340 small block engine builds.  Please include what ignition you used.  And...

Started by Cuda CodyView the profile of Cuda Cody

Replies: 9
Views: 11,861

June 06, 2017, 08:32:59 PM
by Chryco Psycho

Fuel lines shipping Hello,I would like to buy 2 3/8 fuel lines to install Fitech injection on my Challenger.I Received a...

Started by chal340View the profile of chal340

Replies: 11
Views: 1,711

June 06, 2017, 08:04:55 PM
by Chryco Psycho