Engine, Transmission & Rear End

stroker builds Tough subject to tackle every build is unique & has perameters to fit into 400 low deck 2 choices u...

Started by Chryco PsychoView the profile of Chryco Psycho

Replies: 1
Views: 1,062

May 27, 2017, 08:30:42 AM
by 303 Mopar

What gears in a833 I'm gonna order a refurbished a833 tranny now for my -73 project with a 5.7 Hemi, got 3:23 in the re...

Started by soundcontrolView the profile of soundcontrol

Replies: 12
Views: 4,027

May 26, 2017, 09:45:53 AM
by Cuda Cody

Recommendations for Wideband Air Fuel Gauge kit Will be looking to buy in about 4-6 weeks. Wondering what's out there and what to look or look out f...

Started by Cudakiller70View the profile of Cudakiller70

Replies: 10
Views: 1,573

May 23, 2017, 09:19:01 PM
by Cudakiller70

Rebuilding a 67 383 motor to put in front of 4-speed trans Hello, i will soon be in a process of rebuilding the 383 motor in my Challenger, i will convert my c...

Started by SlyView the profile of Sly

Pages1 2

Replies: 26
Views: 2,842

May 23, 2017, 09:01:11 AM
by Chryco Psycho

Dual Quad Manifold for 360 Mopar What is a good Dual Quad Manifold for 360 Mopar? Presuming a 318 or 340 dual quad manifold should fi...

Started by CudaMoparRayView the profile of CudaMoparRay

Pages1 2

Replies: 17
Views: 6,501

May 22, 2017, 04:50:34 PM
by Chryco Psycho

Slip yoke ID? I need help determining what slip yoke for a 73 4spd w/8.75 rear. Can anyone help me determine what ...

Started by ValkmanView the profile of Valkman

Replies: 6
Views: 1,223

May 22, 2017, 10:43:56 AM
by Cuda Cody

Drive shaft length and dimension I have a 1970 Cuda, it has the A31 option.  It's a 383 its suppose to have a sure-grip, 3.91 axle. I...

Started by jlemlerView the profile of jlemler

Replies: 1
Views: 932

May 22, 2017, 07:16:48 AM
by anlauto

Cam install retainer hitting seal Supposed to have about .060 clearance between retainer and seal. I can see the retainer pushing on t...

Started by Cudakiller70View the profile of Cudakiller70

Replies: 9
Views: 1,324

May 21, 2017, 05:57:14 PM
by Cudakiller70

Six Pack Vacuum Hose Routing My engine is finally on the dyno. Its a 440 SIx Pack, I have ordered a cam from Mr. Six Pak. I need ...

Started by Car-nuttView the profile of Car-nutt

Replies: 2
Views: 5,776

May 21, 2017, 01:45:42 PM
by anlauto

833 reverse lights wiring Installing my first 833 in an e-body and I am not sure how the reverse light wiring is connected.  T...

Started by 303 MoparView the profile of 303 Mopar

Replies: 12
Views: 5,457

May 18, 2017, 11:24:42 AM
by Cuda Cody

Recommended throttle cable '70 'Cuda, 440, 4-speed, Holley dominator intake, and Quick Fuel 880 CFM carb.  I purchased the pict...

Started by usraptorView the profile of usraptor

Replies: 8
Views: 1,656

May 15, 2017, 06:24:24 PM
by usraptor

Carb spacer busted... oops I've unfortunately broke two tabs on my carb spacer.  Should I replace it?  Next time if it doesn't ...

Started by nsmallView the profile of nsmall

Replies: 10
Views: 1,524

May 15, 2017, 08:22:22 AM
by 303 Mopar

Lockout linkage Anyone know if the 4 speed lockout linkage for a B body is the same as the E body? Or maybe some of ...

Started by SteveGView the profile of SteveG

Replies: 3
Views: 1,072

May 14, 2017, 06:42:17 PM
by Cuda Cody

Question about removing a driveshaft (sort of) I installed a rebuilt 4spd. I put 4qts in it I then capped the tailshaft so it wouldn't leak before ...

Started by ValkmanView the profile of Valkman

Replies: 5
Views: 1,100

May 13, 2017, 08:01:49 PM
by RUNCHARGER

Pedal adjustment? Is there a way to adjust the clutch and/or brake pedals so they line up? The clutch pedal seems out ...

Started by ValkmanView the profile of Valkman

Pages1 2

Replies: 19
Views: 4,211

May 12, 2017, 08:35:09 PM
by Chryco Psycho

Best floor hump for 4-speed conversion Where to find the best floor hump part for a 4-speed conversion ? (Passon four speed trans, McLeod c...

Started by SlyView the profile of Sly

Pages1 2

Replies: 16
Views: 4,524

May 12, 2017, 10:03:24 AM
by 1 Wild R/T

dial timing light Breaking in my engine.  I think I set the dial to 35, run the RPM up around 2800 and turn the dist t...

Started by 70BarracudaView the profile of 70Barracuda

Replies: 6
Views: 1,039

May 12, 2017, 06:40:44 AM
by 70Barracuda

C

Leaky Thermoquad Hi All.  I'm a newbie to Carter Thermoquads, this is my first one to tinker with and rebuild.  As I ...

Started by CudinoView the profile of Cudino

Pages1 2

Replies: 24
Views: 3,387

May 11, 2017, 10:24:07 AM
by Cudino

Found an 18 spline trans. I posted this to Galen and on the E bodies facebook page. Here are those numbers on the tranny........

Started by cudajunctionView the profile of cudajunction

Pages1 2

Replies: 15
Views: 2,147

May 09, 2017, 10:06:19 PM
by cudajunction

Weiand Tunnel Ram 440 Anyone here have any experience with a Weiand tunnel ram on a 440? A buddy mine bought an engine tha...

Started by dave73View the profile of dave73

Replies: 7
Views: 980

May 08, 2017, 11:47:40 AM
by ec_co