Wheels, Tires, Brakes, Suspension & Steering

W

E-Body Tire Sizes (what fits, what's too big, what looks good) I know this has been asked  many times  but what size tires would look good on my challenger with 15...

Started by Timbbuc2View the profile of Timbbuc2

Pages1 2 3 ... 13

Replies: 193
Views: 138,406

February 17, 2025, 04:20:25 PM
by whitsend

Rallye 15-inch trim rings summary I'm looking to switch to 15-inch rims and have been doing a lot of research on finding correct trim ...

Started by 70pumpkinView the profile of 70pumpkin

Pages1 2

Replies: 19
Views: 30,377

October 13, 2023, 08:57:37 AM
by 70pumpkin

Understanding Suspension and How to Make Your Car Handle Corners Better Hello, this is Tavis King again.  I'm usually over on our E-Bodies.org Facebook group, where I help ...

Started by cataclysm80View the profile of cataclysm80

Pages1 2

Replies: 28
Views: 8,304

September 28, 2023, 06:33:15 AM
by BIGSHCLUNK

Rear Drum Brake Build The purpose of this thread is for pointers and reference in rear drum brake overhaul. This was done ...

Started by Shane KelleyView the profile of Shane Kelley

Pages1 2 3

Replies: 44
Views: 45,532

February 28, 2022, 09:49:44 AM
by anlauto

Using C-Body spindles on an E-Body ( and A-Body LCA's & Viper calipers) ( This thread is a copy, from our old site) I'm going to modify C-Body spindles to fit on my 1970 Ch...

Started by Brads70View the profile of Brads70

Pages1 2 3

Replies: 39
Views: 45,320

November 15, 2020, 04:55:24 AM
by Dakota

Torsion bars vs coil springs             Is there an advantage ie. weight reduction, cost. to using bars rather than springs? I t...

Started by RoadmanView the profile of Roadman

Pages1 2

Replies: 27
Views: 34,997

September 15, 2020, 06:55:20 AM
by RUNCHARGER

M

Anyone have a PST manual steering box? Is any one here using a PST manual steering box?I just bought their 20:1 ratio manual box. When I op...

Started by 7dcudaView the profile of 7dcuda

Replies: 3
Views: 287

March 27, 2025, 05:45:26 PM
by Mopar5

M

Suspension Looking for some opinions I have new tie rods Pitman arm and idler arm set in place with the steerin...

Started by Mopar5View the profile of Mopar5

Replies: 0
Views: 53

March 27, 2025, 05:42:25 PM
by Mopar5

M

Emergency Brake Pedal Doesn't Return I bought a 70 Barracuda a couple of weeks ago. I'm fixing a lot of little things. I noticed the emer...

Started by money pitView the profile of money pit

Replies: 7
Views: 257

March 27, 2025, 09:45:47 AM
by money pit

C

Park brake pedal release bushing Someone recently posted an after market part number for the nylon bushing any body know what it is

Started by Ns1aarView the profile of Ns1aar

Replies: 2
Views: 444

March 25, 2025, 08:03:45 PM
by Cassanth

C

1970 Challenger parking brake lever, need a picture? So I was going over my car today getting it ready for the season when I tried my e-brake. It went li...

Started by Brads70View the profile of Brads70

Pages1 2

Replies: 22
Views: 7,861

March 25, 2025, 08:02:13 PM
by Cassanth

M

Leaf Spring Restoration Question Hey all, recently had my leaf springs restored, and was re-reading the thread below and noticed the ...

Started by 70_440-6CudaView the profile of 70_440-6Cuda

Replies: 4
Views: 363

March 20, 2025, 11:48:55 AM
by mtull

M

Which direction is the rotor inner grease seal installed? 1973 Challenger.I don't remember seeing a grease seal with a long lip like this before.Is the seal i...

Started by RayLView the profile of RayL

Replies: 14
Views: 367

March 14, 2025, 11:15:46 AM
by mtull

X

USCT Level 1 kit installation  Hello all. I'm looking for shop installation recommendations for a USCT Level 1 kit, in the Manteca...

Started by rikkitikView the profile of rikkitik

Replies: 5
Views: 240

March 07, 2025, 05:47:03 PM
by Xghobo

M

Proportioning Valve Special Socket/Tool There's a special socket used to remove the valve from the proportioning block.  I can't find any re...

Started by mtullView the profile of mtull

Replies: 7
Views: 475

March 06, 2025, 11:34:49 AM
by mtull

drum brake master cylinder date stamp format I'm trying to understand how to read the assembly date on drum brake master cylinders.  I've seen me...

Started by mtullView the profile of mtull

Replies: 7
Views: 271

March 04, 2025, 05:04:08 PM
by JH27N0B

Help needed on MP Leaf Springs Fitment Advice I have installed my leaf springs on my 70 Challenger restoration thinking they were original but now...

Started by valmanView the profile of valman

Replies: 12
Views: 486

March 03, 2025, 09:29:12 AM
by MoparLeo

Master Cylinder cover gasket needed I am unable to find the one I have through ebay, summit, jegs, roseville,etc. It has the Pentastar o...

Started by Racer57View the profile of Racer57

Replies: 2
Views: 196

March 01, 2025, 07:40:51 AM
by Racer57

M

Brake block plug I need a plug for a brass brake safety valve/proportioning valve. It is brass with a 5/16 head on it...

Started by XghoboView the profile of Xghobo

Replies: 3
Views: 184

February 27, 2025, 05:21:24 PM
by mtull

Pitman & Idler arm & Tie rods This Challenger has been sitting too long and I need to get it done . I need to get the Pitman arm ,...

Started by Mopar5View the profile of Mopar5

Replies: 5
Views: 380

February 24, 2025, 12:54:31 PM
by GUMM B