Main Menu

Wiper motor spacers

Started by fireguyfire, March 08, 2020, 05:17:10 PM

Previous topic Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages1
User actions

fireguyfire

March 08, 2020, 05:17:10 PM
Putting things back into my firewall after painting my engine bay.
I'm in bagging parts I removed and I realize that I only have 2 of the flared aluminium spacers that go onto the 3 studs of the wiper motor.
I'm assuming I should have 3?

Dakota

#1
March 08, 2020, 05:35:24 PM
I had 3 spacers on my wiper motor.  I think you're missing one.

anlauto

#2
March 08, 2020, 06:44:44 PM
Stephan @SF-Resto might have one ?
I've taught you everything you know....but I haven't taught you everything I know....
Check out my web site ....  Alan Gallant Automotive Restoration

fireguyfire

#3
March 08, 2020, 06:55:45 PM
What a pain to be missing 1 cheap aluminum spacer!

Ns1aar

#4
March 08, 2020, 07:07:19 PM
It maybe still be on the stud or hidden in one of the rubber bushings been there done that

anlauto

#5
March 08, 2020, 07:22:17 PM
Quote from: Ns1aar on March 08, 2020, 07:07:19 PM
It maybe still be on the stud or hidden in one of the rubber bushings been there done that

Yup...very common to stay on the stud
I've taught you everything you know....but I haven't taught you everything I know....
Check out my web site ....  Alan Gallant Automotive Restoration

Shoooter

#6
March 08, 2020, 08:34:02 PM
I agree,  mine stayed on the stud... it was a pain to get off after

fireguyfire

#7
March 09, 2020, 05:09:28 AM
When installing these spacers, does the flare end go in towards the firewall, or out towards the wiper motor?

anlauto

#8
March 09, 2020, 05:21:44 AM
Firewall :bigthumb:
I've taught you everything you know....but I haven't taught you everything I know....
Check out my web site ....  Alan Gallant Automotive Restoration

SF-Resto

#9
March 09, 2020, 05:23:19 AM
These  are the spacers. I had a few made. They were steel not aluminium. They are install with flanges against firewall

Top are for 2 pieces  ( Foam gasket & rubber grommets )Bottom are for one piece gasket  ( B Body )


Stephan
 



fireguyfire

#10
March 09, 2020, 05:49:31 PM
So these are the 2 spacers I have; someone mentioned these go on after the wiper motor, between the wiper motor and the nuts, and that there should be 3 different style spacers that go between the wiper motor and the firewall.
Is this correct? Does someone have a photo showing the correct configuration?

SF-Resto

#11
March 10, 2020, 05:23:27 AM
Quote from: fireguyfire on March 09, 2020, 05:49:31 PM
So these are the 2 spacers I have; someone mentioned these go on after the wiper motor, between the wiper motor and the nuts, and that there should be 3 different style spacers that go between the wiper motor and the firewall.
Is this correct? Does someone have a photo showing the correct configuration?

Your spacers are put in the right side but they  usually are put in in the grommets first then you can slide your motor on the studs and tighten . ( The little notch on the spacers is there to hold them on the grommets )

RUNCHARGER

#12
March 10, 2020, 08:52:16 AM
Yup: Spacers first. Do you have the correct nuts for them?
Sheldon

fireguyfire

#13
March 10, 2020, 11:15:59 AM
I have the correct factory 3 nuts, but just the 2 spacers.
I'm assuming the holes in the new wiper motor gasket are bigger and go over the spacers?
Print
Go Up Pages1
User actions

Similar Topics