Main Menu

Charging issues - Still need help

Started by Spikedog08, June 08, 2018, 07:05:08 AM

Previous topic Next topic

0 Members and 4 Guests are viewing this topic.

RUNCHARGER

Electric fans pull a ton of current. A stock style 70's alternator isn't going to come close to keeping up at idle. The VR's get hot but they've been in that spot for a lot of years.
Sheldon

chargerdon

Are you running stock wiring ?   Or modified for the alternator lead thru the bulkhead connector...??    if stock that has always been a source of problem, doesnt take a lot of corrosion on the bulkhead connector to have an issue passing that much current thru the bulkhead connector...   That would be my guess if the VR is ok.   

YellowThumper

Had same issue with mine for a long time. Definitely check grounding. Some of the VRs I purchased were even painted on underside face where they bolt to firewall. Scrape that off to get metal contact. If you are still wired up for the normal bulkhead connections. I would suspect that to be an issue. Especially with electric fans. At minimum they should be powered direct bypassing bulkhead and amp gauge. My issue ended up being low and erratic signal voltage. Iirc it is the blue wire. Its voltage should be real close to output voltage. I checked mine by getting baseline voltage from battery with car not running. Then check signal wire voltage. Mine registered over 1.5 volts lower. Ended up bypassing car wiring and ran new setup triggered with relays.

Good luck
Mike
Life is to be viewed thru the windshield. Not rear view mirror.
You are the only one in charge of your destiny.

Mike.


73chalngr

With the battery disconnected see if the ammeter studs are loose they should not wiggle at all.  I bought rallye gauges on eBay when I went to install them my ammeter would indicate charging then not charging the studs were loose. Had to have it repaired. I did not check if I had signals or anything else but just about everything on inside of firewall goes through that connection.

tdwnilla1

Check connection number 18 at bulkhead

chargerdon

Your problem could be almost anywhere.   There are wiring diagrams available for free at http://www.mymopar.com/index.php?pid=27

Places i would check in order:

1) tight wires at the alternator
2) Make sure VR has good ground, and try replacing and see if it corrects problem.   
3) All of the wiring connections...  simplified...
A) power runs from alternator, there is a single disconnect behind distributor in the engine wiring harness..  from there
b)  into the bulkhead connector.   I believe post 18 this will be a heavy Black wire.   This will often with age get corrosion making a less than full contact...   Definitely remove the bulkhead connector and check both the male and female connectors for corrosion and clean.   c) From there it runs into a splice in the dash wiring that in turn feeds most of the factory systems.
   Not easy to check there but it could be a source of problem.   
4) From the dash harness splice it runs into the amp meter.   Again, not real easy to check, but, certainly if any of the nuts on the amp meter have come loose then intermittent results are possible.   
5) From the amp meter, a Red wire then back thru bulkhead connector i believe on post 16 (middle bulkhead connector).   This is a heavy red wire.   Again check that connector for corrosion.   Look for any signs of overheating !!!!!
6) On engine side the red wire in post 16 is supposed to be a fusible link which runs to the starter relay and then to battery.   

The voltage regulator pos input comes from a splice in the engine compartment wiring harness, and the field terminal wire runs thru engine connector in engine wiring harness..you will find behind distributor, and onto the field post on the alternator.   I believe that wire runs thru connecetor post 1. You might want to check for corrosion on it.   

Lastly, but unlikely is that the alternator itself has a diode or two that is beginning to fail.   

Hope you get lucky and the VR replacement fixes it...   Incidently, look carefully at the bulkhead connectors for signs of overheating...that is a heavy spot for failure...   

Spikedog08

I know this is an old thread but I still have the same issue and I hope this winter I can get to the bottom of the problem.  Electricity is not my strong suit but I need to learn so I may ask a whole lot of questions and some may be (probably be)  stupid . . . warning in advance. 

I guess the first thing I should do is buy a good meter . . . I bought a cheap one last year and it has already crapped out.   Recommendations please? 

I took the car to a local auto shop and asked for help with this issue, after 4 days and $400, I was told 1 wire was not thick enough and was replaced somewhere by the battery  . . . waste of money.  I called another Mopar/auto shop and they didn't want to help . . kept putting me off and then said they would call me when they had an opening.  Been months now . . .

So this is a project I have planned this cold season . . . thanks for all the help in advance! 


First thing I will do is go through the list chargerdon posted above . . . and go from there.
Drive it like you stole it . . . And they're CHASING you!


6pack

Are you running a thick wire fan feed relay right off the battery? The sensors should turn on the relay.  Everything needs to be appropriately fused.

Spikedog08

Quote from: 6pack on September 24, 2019, 09:34:34 AM
Are you running a thick wire fan feed relay right off the battery? The sensors should turn on the relay.  Everything needs to be appropriately fused.

Yeah I think it is mounted under the battery tray . . Believe it is all fused properly . . . Worked great for many years . . Then . . . Issues.  I know when the guys were looking at it in Carlisle . . It was discovered that from the alternator to the battery, somewhere I was losing 2 volts.  Something somewhere is draining or restricting the current flow . . .
Drive it like you stole it . . . And they're CHASING you!

Chryco Psycho

$400 for nothing , I really am not charging enough !!
I could fly in & save you $$ except there is a glitch with that too  :Thud:
I would start with a simple voltage test , how many volts do you have at the battery & what does it drop too with everything on , it would  not surprise me if you need a higher output alt except that it was working ok before  :thinking:
Klein & Fluke are great meters but overpriced like Snap On , I look something with Quality leads as that is usually the first thing to fail GB & Sperry made decent mid cost meters

Brads70

Quote from: Chryco Psycho on September 24, 2019, 11:03:37 AM

I would start with a simple voltage test , how many volts do you have at the battery & what does it drop too with everything on , it would  not surprise me if you need a higher output alt except that it was working ok before  :thinking:

Quote from: Brads70 on July 09, 2018, 08:02:50 PM
Quote from: Spikedog08 on June 08, 2018, 07:05:08 AM
So I finally got out in one of the cars last night and all seemed good, everything looked normal.  Cruising down the road Alt gauge was where is typically is on the charging side. Minute later look down and it is discharging??  Then as I'm looking at it . . . it bounces back to the charging side.  Everything is pretty new but it appears that I have a loose connection somewhere??  I checked everything on the alternator and nothing seems to be loose or corroded? 

So my question is . . . where else should I check?  Where else does the charging circuit run that could have a short?   :notsure:

Might be the electric fan coming on and off? Maybe your alternator can't keep up with the electrical add ons? I ran into that issue with mine  when I ran a stock alternator.

  "Strange thing I noticed is when it is not charging, my turn signals don't work??  Makes me wonder if my brake lights are working as well?"
If the alternator won't keep up maybe there is not enough amperage to run the flasher?  :notsure:

Mine worked"fine" to for awhile ( couple years) till I went on a long drive (Carlisle) and with all the electrical add on's and maybe the battery aging some , the stock alternator just wouldn't keep up.  Short 1/2 trips around town was fine ..... until it wasn't. at least 8 months a year the car was not in use and on a charger.  I'd say any electric cooling fan will draw more power than the stock system was designed to output.  your trying to get 20lbs of potatoes out of a 10 lbs sack?
Dave if you want I have a spare alternator I could mail you to try? Its one of those high output Quality power units but wired for 1 wire hookup


Spikedog08

Thanks @Brads70 !  Very nice of you to offer.  For my $400 that I paid the last mechanic, he did tell me there is nothing wrong with the alternator as was also determined in Carlisle when the guys pulled it apart . . It is a serpentine system so that would be an issue as well.  I am gonna learn more about the electronics of these cars one way or another and I guess this is gonna be car electricity 101.  I'm going to Harbor Freight this week and buy a good meter.  Then someone will need to teach me what all the setting are for?  Fun Fun!  Garage is heated so have many plans for the cars! 

Hardtop just needs a lot of detailing and a few small things . . Convertible has this issue and needs some cleaning as well.  Plus I'm pulling the entire dash out for installation of a rallye cluster that I planned to do last year but never got to it.   
Drive it like you stole it . . . And they're CHASING you!

dodj

Losing 2 volts 'somewhere' is dirty/poor connections. Check and clean them all! Including all the places Don mentioned plus the one the pass side valve cover. Star washers on the VR. Take apart and clean the connections at the starter relay. Clean your battery posts. Take apart and check/clean your engine to body grounds.
Don also mentioned it but check your ammeter connections...with the battery disconnected...
Not fun work...but necessary....
Good luck!
"There is nothing your government can give you that it hasn't already taken from you in the first place" -Winston Churchill