Tools and Equipment

R

How are you heating your garage this Winter? I have an unheated 2-car garage that is too cold to work in now (~35F). The space is 20ft by 20ft wi...

Started by RayLView the profile of RayL

Pages1 2

Replies: 27
Views: 2,026

February 12, 2025, 02:58:22 PM
by RayL

Frame rack ideas Working on metal replacement for my 70 Challenger. My first plan morphed into a revised plan but lat...

Started by 70 Challenger LoverView the profile of 70 Challenger Lover

Pages1 2 3

Replies: 41
Views: 6,354

January 08, 2025, 03:52:15 PM
by MoparLeo

Engine run stand I said I would start a thread on my engine run stand, so here it is.  I needed an engine run stand,...

Started by DeezelView the profile of Deezel

Replies: 2
Views: 292

January 03, 2025, 08:06:38 PM
by Deezel

Key Buzzer Tool Inquiry Hi All, I am starting my restoration on my 1970 steering column, and was re-reviewing Cody's excelle...

Started by 1970CudaView the profile of 1970Cuda

Replies: 9
Views: 1,911

September 30, 2024, 06:08:11 PM
by Cuda Cody

I hate welding ... unless it is working Ugh. I'm wrapping up the last few things until I get the car on the road for the first time 30+ year...

Started by tparkerView the profile of tparker

Replies: 1
Views: 744

May 15, 2024, 04:57:27 AM
by dodj

Garage Floor Epoxy Coating I've been wanting to have my garage floor coated with epoxy either professionally or maybe doing it ...

Started by BlowoutView the profile of Blowout

Replies: 12
Views: 3,550

March 27, 2024, 07:06:45 PM
by EDL94

Air Compressor Recommendation Every now and then, someone asks for a compressor recommendation. I've been researching them for a c...

Started by 70 Challenger LoverView the profile of 70 Challenger Lover

Replies: 6
Views: 1,892

February 17, 2024, 09:23:30 AM
by 70 Challenger Lover

Best Welder for Automotive - Can I do this? I've been putzing around with cars half my life, but have never really learned to weld...I borrowed ...

Started by 392 CudaView the profile of 392 Cuda

Pages1 2

Replies: 24
Views: 4,804

February 10, 2024, 05:06:28 AM
by 70 Challenger Lover

N

Used Rotisserie Used Auto Lift CR 3000 Car Rotisserie. Currently set up for E-body. In Socal possible delivery1500.0...

Started by Ns1aarView the profile of Ns1aar

Replies: 0
Views: 448

January 30, 2024, 07:11:15 PM
by Ns1aar

Snap on torsion bar gauge Found this going through some old tools from my fathers gas station back in the day. Not sure exactl...

Started by Rich G.View the profile of Rich G.

Replies: 1
Views: 1,035

January 25, 2024, 09:48:07 AM
by EV2RTSE

Lisle 59000 valve guide cutter/reamer/liner install tool This toolset allows you to do valve guide replacement without large machinery; there's a couple of v...

Started by DuodecView the profile of Duodec

Replies: 1
Views: 3,320

October 31, 2023, 02:38:12 PM
by Duodec

R

Torque Wrench Recommendation Hey guys,I'm looking for a new torque wrench recommendation .  I've always had a mechanical torque w...

Started by DavehView the profile of Daveh

Replies: 12
Views: 2,684

June 26, 2023, 12:16:01 PM
by Racer Dave

DA Sanders Looking to buy an air da sander.  Wanted to see what you guys recommend. Looking for a good value on...

Started by BlowoutView the profile of Blowout

Replies: 3
Views: 1,168

June 05, 2023, 11:51:55 AM
by JS29

7

Door Lift assist for floor jack?? I'm at the point where I'm going to need to take the doors off and on occasionally and working by my...

Started by gzig5View the profile of gzig5

Replies: 2
Views: 692

May 11, 2023, 10:10:36 AM
by 72restocuda

2 post lift recommendations Looking for a lift of around 10,000 pounds to lift a variety of cars , including e bodies, and picku...

Started by Skunkworks ChallengerView the profile of Skunkworks Challenger

Replies: 11
Views: 1,702

March 10, 2023, 10:23:50 AM
by GoMangoBoys

Seeking guidance on flatbed trailors Well I think I am in the market for a flatbed trailer so I can go to some non-local shows/meets. Can...

Started by 70vertView the profile of 70vert

Replies: 1
Views: 592

February 20, 2023, 04:08:52 PM
by RUNCHARGER

One post car lift Anyone using this type of lift? Looked at many YT videos and it seems a bit wobbly, but I really lik...

Started by soundcontrolView the profile of soundcontrol

Replies: 4
Views: 1,025

January 16, 2023, 02:43:57 AM
by soundcontrol

Fuel Injectors Has anybody used a tool like this?https://www.amazon.ca/Automotive-Injector-Gasoline-Non-Dismantle-T...

Started by dodjView the profile of dodj

Replies: 1
Views: 778

January 15, 2023, 03:43:55 PM
by dodj

Welding Helmet suggestions Hey all, did some rosette welding on fuel tank brackets over the weekend and not happy with my place...

Started by JocigarView the profile of Jocigar

Pages1 2

Replies: 24
Views: 5,193

December 10, 2022, 09:31:32 PM
by GoMangoBoys

Torque wrench calibration recommendation: Team Torque Inc. I have an ~8 year old analog (non-digital) Matco torque wrench which stopped "clicking" and otherwis...

Started by DakotaView the profile of Dakota

Replies: 3
Views: 2,458

December 10, 2022, 04:52:52 AM
by torredcuda