project phantom

YellowThumper · August 17, 2020, 08:37:32 AM

Here is a pic from Brewer's website.
Washers and specific style clips.

JonH · August 17, 2020, 09:01:28 AM

turn the reverse rod around...large bend under the crossmember. You need bushings in there as well. Go to Brewers web site to find parts you may need

YellowThumper · August 17, 2020, 09:29:51 AM

Quote from: JonH on August 17, 2020, 09:01:28 AM
turn the reverse rod around...large bend under the crossmember. You need bushings in there as well. Go to Brewers web site to find parts you may need

Pic above from JonH reverse lever is early style that does not go under crossmember. Follow his setup. But know you will have the large sweep bend instead. End result to trans is the same.

Cuda70-74 · August 17, 2020, 12:48:22 PM

Quote from: YellowThumper on August 17, 2020, 09:29:51 AM
Quote from: JonH on August 17, 2020, 09:01:28 AM
turn the reverse rod around...large bend under the crossmember. You need bushings in there as well. Go to Brewers web site to find parts you may need

Pic above from JonH reverse lever is early style that does not go under crossmember. Follow his setup. But know you will have the large sweep bend instead. End result to trans is the same.

That is correct it is a early style

Cuda70-74 · August 17, 2020, 12:49:08 PM

Quote from: YellowThumper on August 17, 2020, 08:37:32 AM
Here is a pic from Brewer's website.
Washers and specific style clips.

Thanks going to have to put a order in for those

Cuda70-74 · August 17, 2020, 01:05:52 PM

Well it looks like the speedway universal gen III 5.7 hemi engine weld-In motor mounts will not work. I was trying to save some money on the motor mount which backfired

. The driver side will fit perfectly but the passenger side is offset

nsmall · August 17, 2020, 09:47:03 PM

These cars are nothing but a pain and money pits but man they are fun to drive when you are done.

Cuda70-74 · August 17, 2020, 10:30:22 PM

Quote from: nsmall on August 17, 2020, 09:47:03 PM
These cars are nothing but a pain and money pits but man they are fun to drive when you are done.

Thats a fact. The cuda is a guinea pig for the gen 3 hemi swap. Should be smooth on my 68 charger since its going to be a auto

Cuda70-74 · August 20, 2020, 11:36:08 AM

The gen 3 hemi is in

This is the motor mount u will need if using a qa1 k member https://www.manciniracing.com/mrebugeniiiadd.html

YellowThumper · August 20, 2020, 12:37:17 PM

Brads70 · August 20, 2020, 04:17:08 PM

Nice progress! That must feel good!

Cuda70-74 · August 20, 2020, 05:39:54 PM

Yes it is. Just need to get the cylinder head done,driveshaft and few other things

Cuda70-74 · August 27, 2020, 12:21:47 PM

Painted my doors with epoxy primer today.

Brads70 · August 27, 2020, 01:54:10 PM

OHHH and a Charger too, 68 no less! I'm envious!

Cuda70-74 · August 27, 2020, 02:40:47 PM

Quote from: Brads70 on August 27, 2020, 01:54:10 PM
OHHH and a Charger too, 68 no less! I'm envious!

68 my favorite year for the charger. She next in line after the cuda

Phantom Cuda carcass (Graveyard Carz) Started by Cuda Cody on Cuda & Challenger General Discussion (ROSEVILLE MOPARTS)	20 Replies 8216 Views	Last post: July 11, 2017, 06:30:11 PM by anlauto
My new project Started by xx88man on Cuda & Challenger General Discussion (ROSEVILLE MOPARTS)	55 Replies 4334 Views	Last post: April 03, 2017, 05:26:40 PM by Blake@diyhemi.com
My AAR project Started by 6Pack70 on Your Restoration project (ROSEVILLE MOPARTS)	207 Replies 14685 Views	Last post: January 14, 2020, 08:57:33 AM by JS29
new here with a big project Started by cuda-jay on New Members Introductions (ROSEVILLE MOPARTS)	31 Replies 2463 Views	Last post: August 28, 2019, 08:59:37 PM by nsmall
New project for A.G.A.R. Started by anlauto on Your Restoration project (ROSEVILLE MOPARTS)	30 Replies 2528 Views	Last post: November 08, 2018, 07:57:57 AM by Spikedog08