project phantom

[Cuda70-74]

Thanks guys. Got it to go back in looks like i had to shave a little bit more off the input shaft.

[YellowThumper]

Great to hear

[soundcontrol]

What clutch and flywheel did you get?
I still have not bought those parts for my 73 project with a 5.7 / 833a.

[Cuda70-74]

Here is the pressure plate bolts
https://www.summitracing.com/parts/ARP-130-2201
Here is the clutch kit
https://www.summitracing.com/parts/MCL-75109
Here is the flywheel
http://www.brewersperformance.com/proddetail.php?prod=FW400

[soundcontrol]

Here is the pressure plate bolts
https://www.summitracing.com/parts/ARP-130-2201
Here is the clutch kit
https://www.summitracing.com/parts/MCL-75109
Here is the flywheel
http://www.brewersperformance.com/proddetail.php?prod=FW400

Thanks! 

[Cuda70-74]

Hi need some help again on installing these linkage rod. Is it easier to install the linkage while engine and tranny  is out of the car or when its in the car?

[RUNCHARGER]

Adjust it before installing in car. You will have to pull it off before installing the trans into the car though.

[JonH]

Out... but put the trans crossmember on the trans first, assuming you are putting the engine/trans in from the bottom..

[Cuda70-74]

Adjust it before installing in car. You will have to pull it off before installing the trans into the car though.

Thanks how do you go about adjusting them. First time working with a tranny with external linkage

[Cuda70-74]

Out... but put the trans crossmember on the trans first, assuming you are putting the engine/trans in from the bottom..

Im putting the engine in the old school way using a engine hoist

[YellowThumper]

Adjust it before installing in car. You will have to pull it off before installing the trans into the car though.

Thanks how do you go about adjusting them. First time working with a tranny with external linkage

With shifter installed. There is a hole thru all the arms. When in neutral they all line up. Put a pin in to keep them located. Pin, bolt, allen wrench can work also. Ensure all trans levers are in neutral. Then adjust till post from bars drop in freely to hole on bracket. Prior to disassembly, you can mark the positions. Marker, wrap with tape, etc... I have used zip ties fore and shaft also. Basically whatever you have on hand.

[Cuda70-74]

Adjust it before installing in car. You will have to pull it off before installing the trans into the car though.

Thanks how do you go about adjusting them. First time working with a tranny with external linkage

With shifter installed. There is a hole thru all the arms. When in neutral they all line up. Put a pin in to keep them located. Pin, bolt, allen wrench can work also. Ensure all trans levers are in neutral. Then adjust till post from bars drop in freely to hole on bracket. Prior to disassembly, you can mark the positions. Marker, wrap with tape, etc... I have used zip ties fore and aft also. Basically whatever you have on hand.

Thanks

[Cuda70-74]

Need some help on putting these rods on. These linkage rod are for 73-74 cuda and im lost on how to install the last 2.

[YellowThumper]

Need some help on putting these rods on. These linkage rod are for 73-74 cuda and im lost on how to install the last 2.

If no one helps today a can give you pics of my setup. Same rods as yours. Will be about 12 hours though.

The long large loop one is I believe reverse. Loop is towards rear and loops under trans mount crossmember. Perfect placement (sarcasm)  for speed bump contact. Roll over a speed bump at normal speed and that is where car squats when coming down. It will become a familiar sound...

[Cuda70-74]

Need some help on putting these rods on. These linkage rod are for 73-74 cuda and im lost on how to install the last 2.

If no one helps today a can give you pics of my setup. Same rods as yours. Will be about 12 hours though.

The long large loop one is I believe reverse. Loop is towards rear and loops under trans mount crossmember. Perfect placement (sarcasm)  for speed bump contact. Roll over a speed bump at normal speed and that is where car squats when coming down. It will become a familiar sound...

Thanks. I think i might have to wrong crossmember because the reverse rod wont bolt up to the shifter. Another question is it only a clip that hold the shitfer rod in??